HUASHENG PRECISION · Updated November 20, 2026
Tap drill size chart: metric and Unified threads, clearance holes and counterbores
Tap drill sizes for metric and Unified threads, with clearance hole, counterbore and countersink dimensions for the matching screws. Reference values from the screw thread and fastener standards.
Metric coarse thread tap drill sizes
Tap drill diameters for ISO metric coarse threads. The values follow the usual rule, tap drill = nominal diameter − pitch, rounded to a common drill size where needed (for example 6.75 to 6.8 for M8).
Swipe horizontally to read the table.
| Thread | Pitch (mm) | Tap drill (mm) |
|---|---|---|
| M1.6 | 0.35 | 1.25 |
| M2 | 0.4 | 1.6 |
| M2.5 | 0.45 | 2.05 |
| M3 | 0.5 | 2.5 |
| M4 | 0.7 | 3.3 |
| M5 | 0.8 | 4.2 |
| M6 | 1 | 5.0 |
| M8 | 1.25 | 6.8 |
| M10 | 1.5 | 8.5 |
| M12 | 1.75 | 10.2 |
| M14 | 2 | 12.0 |
| M16 | 2 | 14.0 |
| M18 | 2.5 | 15.5 |
| M20 | 2.5 | 17.5 |
| M24 | 3 | 21.0 |
Metric fine thread tap drill sizes
Swipe horizontally to read the table.
| Thread × pitch | Tap drill (mm) |
|---|---|
| M8 × 1 | 7.0 |
| M10 × 1.25 | 8.8 |
| M10 × 1 | 9.0 |
| M12 × 1.5 | 10.5 |
| M12 × 1.25 | 10.8 |
| M14 × 1.5 | 12.5 |
| M16 × 1.5 | 14.5 |
| M20 × 1.5 | 18.5 |
For a pitch not listed, subtract the pitch from the nominal diameter. Cut taps and forming (roll) taps use different hole sizes; these values are for cut taps.
Unified (UNC / UNF) tap drill sizes
Commonly published tap drills for Unified inch threads, giving approximately 75% thread engagement.
Swipe horizontally to read the table.
| Thread | Series | Tap drill | Decimal (in) | mm |
|---|---|---|---|---|
| #2-56 | UNC | #50 | 0.0700 | 1.78 |
| #4-40 | UNC | #43 | 0.0890 | 2.26 |
| #6-32 | UNC | #36 | 0.1065 | 2.71 |
| #8-32 | UNC | #29 | 0.1360 | 3.45 |
| #10-24 | UNC | #25 | 0.1495 | 3.80 |
| #10-32 | UNF | #21 | 0.1590 | 4.04 |
| 1/4-20 | UNC | #7 | 0.2010 | 5.11 |
| 1/4-28 | UNF | #3 | 0.2130 | 5.41 |
| 5/16-18 | UNC | F | 0.2570 | 6.53 |
| 5/16-24 | UNF | I | 0.2720 | 6.91 |
| 3/8-16 | UNC | 5/16 | 0.3125 | 7.94 |
| 3/8-24 | UNF | Q | 0.3320 | 8.43 |
| 7/16-14 | UNC | U | 0.3680 | 9.35 |
| 1/2-13 | UNC | 27/64 | 0.4219 | 10.72 |
| 1/2-20 | UNF | 29/64 | 0.4531 | 11.51 |
Millimetre values are converted from the decimal inch size.
Clearance holes for metric screws (ISO 273)
Through-hole diameters for bolts and screws in three series. The medium series is the usual default when a drawing gives no other requirement.
Swipe horizontally to read the table.
| Thread | Fine (mm) | Medium (mm) | Coarse (mm) |
|---|---|---|---|
| M3 | 3.2 | 3.4 | 3.6 |
| M4 | 4.3 | 4.5 | 4.8 |
| M5 | 5.3 | 5.5 | 5.8 |
| M6 | 6.4 | 6.6 | 7 |
| M8 | 8.4 | 9 | 10 |
| M10 | 10.5 | 11 | 12 |
| M12 | 13 | 13.5 | 14.5 |
| M16 | 17 | 17.5 | 18.5 |
| M20 | 21 | 22 | 24 |
Counterbore dimensions for socket head cap screws
Head dimensions follow ISO 4762 (JIS B 1176). The hole and counterbore sizes are the reference values widely used for socket head cap screws; H′ leaves the head slightly proud of the surface and H″ sinks it below the surface.
Swipe horizontally to read the table.
| Screw | Head dia. dk | Head height k | Bolt hole d′ | Counterbore dia. D′ | Depth H′ | Depth H″ |
|---|---|---|---|---|---|---|
| M3 | 5.5 | 3 | 3.4 | 6.5 | 2.7 | 3.3 |
| M4 | 7 | 4 | 4.5 | 8 | 3.6 | 4.4 |
| M5 | 8.5 | 5 | 5.5 | 9.5 | 4.6 | 5.4 |
| M6 | 10 | 6 | 6.6 | 11 | 5.5 | 6.5 |
| M8 | 13 | 8 | 9 | 14 | 7.4 | 8.6 |
| M10 | 16 | 10 | 11 | 17.5 | 9.2 | 10.8 |
| M12 | 18 | 12 | 14 | 20 | 11 | 13 |
| M16 | 24 | 16 | 18 | 26 | 14.5 | 17.5 |
| M20 | 30 | 20 | 22 | 32 | 18.5 | 21.5 |
All values in mm. If a washer is used or the head must sit at a specified depth, state the counterbore diameter and depth on the drawing.
Countersink for flat head socket screws (ISO 10642)
ISO 10642 countersunk head screws have a 90° head. The theoretical maximum head diameter below is the countersink diameter that seats the head flush.
Swipe horizontally to read the table.
| Screw | Head dia. dk, theoretical max (mm) |
|---|---|
| M3 | 6.72 |
| M4 | 8.96 |
| M5 | 11.20 |
| M6 | 13.44 |
| M8 | 17.92 |
| M10 | 22.40 |
| M12 | 26.88 |
| M16 | 33.60 |
| M20 | 40.32 |
Inch flat head screws normally use an 82° head. State the screw standard and the countersink angle on the drawing.
Drill sizes for wire thread inserts
A wire thread insert needs a larger hole and a dedicated STI tap. The drill diameters below are the values published by one insert manufacturer for metric coarse threads.
Swipe horizontally to read the table.
| Thread | Pitch (mm) | Drill before tapping (mm) |
|---|---|---|
| M3 | 0.5 | 3.2 |
| M4 | 0.7 | 4.2 |
| M5 | 0.8 | 5.2 |
| M6 | 1 | 6.3 |
| M8 | 1.25 | 8.4 |
| M10 | 1.5 | 10.5 |
| M12 | 1.75 | 12.5 |
Source: Böllhoff HELICOIL Plus catalogue, suitable twist drill diameter. Other makers publish slightly different values (for example 3.15 mm for M3); use the data of the insert actually specified.Böllhoff HELICOIL Plus カタログ(英語)。メーカーによって数値が少し異なります(M3 を 3.15 mm とする資料もあります)。実際に使用するインサートのメーカー資料に従ってください。
What to state on the drawing
State the thread designation and standard, the tolerance class if it matters, the usable thread depth and whether the hole is through or blind. Leave the tap drill size to the shop unless the hole diameter itself is functional.
For blind holes, give the usable thread depth and the maximum drill depth separately. For counterbores and countersinks, give the diameter, depth or angle, and the screw standard the feature is designed for.
Frequently asked questions
What size drill do I use for an M6 tap?
For an M6 × 1 coarse thread, a 5.0 mm tap drill.
What size drill do I use for an M8 × 1.25 tap?
A 6.8 mm tap drill. For M8 × 1 fine thread, use 7.0 mm.
What is the tap drill for 1/4-20?
A #7 drill, 0.2010 in (5.11 mm), is the commonly published size for about 75% thread engagement.
What is the clearance hole for an M6 screw?
ISO 273 gives 6.4 mm (fine), 6.6 mm (medium) and 7 mm (coarse). The medium series is the usual default.
Standards and references
- ISO 2306 / JIS B 1004 — drills for tapping screw threads
- ISO 273 / JIS B 1001 — clearance holes for bolts and screws
- ISO 4762 / JIS B 1176 — hexagon socket head cap screws
- ISO 10642 / JIS B 1194 — hexagon socket countersunk head screws
- ASME B1.1 — Unified inch screw threads
The values on this page are reference data from the standards and sources named above. They are not statements of our manufacturing capability, stock or lead time.